1sec
Recent posts
- Capturing traffic to br2 interface in promiscuous mode
I dont have any writeup on Security Onion, but i remember it being difficult to get everything set up and visible. Most important thing is getting your antsle interface set up for promiscuous mode,…
- after running upgrade to 0.12, cannot access the GUI
Since the recommended steps on the docs.antsle page didnt seem to work, i was able to obtain a 2nd USB drive and followed your recommended steps for the rollback, everything seems to be working ok…
- after running upgrade to 0.12, cannot access the GUI
Are you saying that the docs page instructions here https://docs.antsle.com/tshoot/#edgelinux-upgrade-rollback will not work?? I dont have a 32G stick. I did try using the systemrescue.iso on a 4GB…
- after running upgrade to 0.12, cannot access the GUI
Running the upgrade-edgelinux command is not working, so i guess i will have to revert it and then try running the upgrade again. I'm using the Antsle one Pro, does that matter? SN starts with 1002-6…
- after running upgrade to 0.12, cannot access the GUI
Thanks for the tip, i've already tried port 3000, doesnt work still (connection refused). I see by Nmap port 443 and others are all showing up. the avahi-daemon service was running, tried restarting…
- after running upgrade to 0.12, cannot access the GUI
Seems like upgrade finished, and service command is back, which is nice. However i'm still unable to connect to the GUI, unfortunately. All i get is 'Bad Gateway'. nginx/1.14.2 - after upgrade-antman…
- after running upgrade to 0.12, cannot access the GUI
its looking promising. after that installed i went ahead and ran upgrade-antman, which seems to be running, however its been sitting at "migrating openRC scripts" for about an hour now. Hope its not…
- after running upgrade to 0.12, cannot access the GUI
its not there. i have done service antsle start/stop and upgrade from the CLI before so it used to work. root@antsle:/sbin # service anthill status zsh: command not found: service root@antsle:/sbin #…
- after running upgrade to 0.12, cannot access the GUI
version showing is: curl http://central.antsle.com/api/antman-info {"version":"2.1.0c","edgeLinux-version":"2.1.0c","anthilld-version":"1.2.7","ear it seems as if the command 'service' has been…
- unable to access GUI after trying to upgrade edgelinux
I can no longer access my GUI, i am able to SSH to it, and also my antlets are running fine. when i issue command service antman status, or other similar commands, i get 'command not found'. How can…
- after running upgrade to 0.12, cannot access the GUI
Able to SSH to the antsle, Antlets are up and running. Cannot access GUI. From CLI, running 'service antman status' or 'service anthill status' returns "Command not found: service". How can i check…
- Running snort IDS in in antlet
following up, got this working. copying reply from my original post-- For promiscuous mode you can install the bridge-utils. from the antsleOS command line run emerge bridge-utils Then set the ageing…
- Capturing traffic to br2 interface in promiscuous mode
I got this working with a little help from Antsle Support (they have been awesome!!) I'm not certain if i still need the commands i issued to turn on the promiscuous mode at the interface, but i am…
- Running snort IDS in in antlet
Hi Alistair, just saw your post. I've been trying to get an IDS working by spanning a port from my external switch to br2 using Ubuntu VM. I manually set the BR2 port for promiscuous mode, however…
- Capturing traffic to br2 interface in promiscuous mode
I'm trying to set up an Intrusion Detection System using Security Onion, Bro, ELSA, and wireshark. I have my internet connection external port spanned from a switch and trying to send the mirrored…